"TEST" button4.In one step, the MicroMapper can test twisted pair cabling for opens, shorts, reversed, crossed, and split pairs. You can use the series of LED light to verify your testing result. It also has a tone generator function which can be used with the MicroProbe cable tracer to trace cables and locate cables hidden in ceilings, walls, floors, and bundles. (Always power the unit off to prevent battery drain. How to Use MicroMapper Testa) Slide the switch on the right side to the "Cable" position to turn MicroMapper on.d) Press the "TEST" button to view the results.e) Use the MicroProbe to trace the connected cable. Generation of two tones for tracing cables and loca It has a moderate price tag ranging aroundtwenty bucks a container, but as soon as you use it you will realize it is wellworth the money.0pt;mso-para-margin-left:0in;line-height:115%;mso-pagination:widow-orphan;font-size:11. It is easy to use and you only have to leave it on for liketen minutes. It also helps smoothout frizz caused by humidity or over processing. The winter brings on the worst dry hair period there is. No matter if you spend your time in the ocean or a pool your hairwill become dry and brittle, which is terrible for colored hair. There is noway you can avoid this in the summer time.Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.So be prepared to use it all year around for the best results.It helps coat the hair to protect it from the sun and free radicals, remember alittle bit goes a long way.0pt;font-family:"Calibri","sans-serif";mso-ascii-font-family:Calibri;mso-ascii-theme-font:minor-latin;mso-hansi-font-family:Calibri;mso-hansi-theme-font:minor-latin;mso-bidi-font-family:"Times New Roman";mso-bidi-theme-font:minor-bidi;}If you use thermal tools a lot you will notice that you havea lot of split ends. It helps repair damageand mend split ends, while helping stop further split ends from appearing. Iteven helps protect the hair from future damage as well. It leaves your hair soft and gets rid of those pesky split endsquickly.You can try just using a bit of strength builder instead of washing your hairto get a finished look just for the night.4pt;mso-para-margin-top:0in;mso-para-margin-right:0in;mso-para-margin-bottom:10.If you live anywhere south of Virginia you know how the humidity can affectyour hair. It works well on wet and dry hair alike. It will coat your hair withoutweighing it down or causing it to turn into a grease ball. What you need is ahair product that will build strength in each hair. These split ends are exist because the ends get the driestand weakest first.4pt 0in 5.

Make sure if you aregoing to be in the water to wash your hair first this will coat the hair andkeep the harsh water or chemicals from stripping it. It is a sign that you have damaged hair..From the water and sun your hair can get burnt so use the strength builder torectify this and deep conditioner your crispy hair. Rememberto plan ahead just because SAE flare flanges the seasons are changing don't think you can dowithout. It is a great inhome hair strengthening treatment. It does this by depositingprotein particle directly into the hair shaft for better results faster. Thisproduct works the first time you use it. You should try offsettingthis effect with redken's extreme strength builder plus. You can try shampooing less but thenyour hair will start to look dirty.MsoNormalTable{mso-style-name:"Table Normal";mso-tstyle-rowband-size:0;mso-tstyle-colband-size:0;mso-style-noshow:yes;mso-style-priority:99;mso-style-parent:"";mso-padding-alt:0in 5.And the tub will last for monthsting hidden cables6.Here is the full list of what the MicroMapper can help you do.1. Auto-sleep mode to decrease power consumption>> What Are on the MicroMapper Unit?The Fluke MicroMapper has a very well designed user interface for easy operation. Toner LED3. The signal reception is strongest near the cable under test. Tests for wiring faults and detects opens, shorts, crossed, reversed, and split pairs. Low Battery LED>> How to Use Fluke MicroMapper?1..f) To find out a fault on a specific pair, use MicroMapper's diagnostic featureg) Press and hold "TEST" button for more than 2 seconds. (To send a tone into a patch panel, connect one end of the included patch cord to the MicroMapper's RJ45 jack and the Turnbuckle Types other end to a jack on the panel.b) Connect one end of the cable to be tested on the MicroMapper's RJ45 jack. REMOTE Adapter with RJ45 jack5.You can use the remote unit for one-person testing of installed cabling. Verifies shield integrity3. Pair and Shield indicator LEDs2.f) Slide the switch on the right side to the "OFF" position to discontinue the tone.75" (40cm))2. If a faulty pair is detected, the corresponding fault status will blink in red.MicroMapper will scan each pair and the shield pausing and flashing each green LED separately. Off/Cable/Toner Switch7. How to Use MicroMapper's Toner Operationa) Slide the switch on the right side of MicroMapper to the "Toner" positionb) Connect the cable to the MicroMapper's RJ45 jack.1.d) To generate tone 2, press and hold the "TEST" button for two seconds. RJ45 jack for the main unit6.c) Connect the other end of the cable to the MicroMapper Remote's RJ45 jack. Green: Pair or Shield is good Green Flashing: Pair or Shield is faulty No Light: Pair is open or cable is not shieldedThe vertical LEDs indicate the wiring faults and a low battery status. Easy to read fault display and high speed testing5. MicroMapper's Remote Identifier enables one person to test installed cabling4. Debug-mode for detailed fault identification results7. Wiring faults are: SHORT, REVERSED, MISWIRE, SPLIT PAIRS. (Split pair fault detection requires a minimum cable length of 15.You need to slide the switch to the "Cable" position, press the "TEST" button and the MicroMapper will then automatically scan for any existing faults in your cable.>> What Can the MicroMapper Help You?Fluke's MicroMapper is a hand-held cable tester that enables network professionals to quickly and easily verify the integrity of Ethernet twisted pair cables.)2.)c) To generate tone 1, press and quickly release the "TEST" button.e) The horizontal LEDs indicate the cable's integrity status. Fault LEDs8